型号: | DHB-3000A |
---|---|
品牌: | 弘测 |
原产地: | 中国 |
类别: | 电子、电力 / 仪器、仪表 / 试验机 |
标签︰ | 布氏硬度计 , 硬度计 , 电子布氏硬度计 |
单价: |
¥19000
/ 件
|
最少订量: | 1 件 |
最后上线︰2019/03/15 |
HC010-HCDHB-3000A型全电子布氏硬度计【小屏显】
HC010-HCDHB-3000A-type all-electronic Brinell hardness [small screen]
产品简介/ Product introduction:
HC010-HCDHB-3000A电子布氏硬度计(全电子布氏)具备了10级试验力,可分别测试布氏硬度的10种标尺.闭环式传感器加载控制系统,高精度、高重复性和稳定性.操作简便。
HC010-HCDHB-3000AElectronicBrinell hardness(fully electronicBrinell)has the10test force,respectivelyBrinell hardnesstestof10 kinds ofscales.Closed loopsensorloadcontrol system,high accuracy, highrepeatability and stabilityoperationis simple.
适用范围/ Scope of application:
电子布氏硬度计采用的试验力大,压痕直经也大,适合具有大晶粒金属材料的硬度测试,如铸铁,有色金属及合金,各种退火、调质处理后的钢材,特别是对于较软的金属,如纯铝、铅、锡等黑色金属,有色金属的布氏硬度测试.
ElectronicBrinell hardnesstest forceused bylargeindentation islarge,suitable for people witha large grainof hardnesstestingof metallic materials,such as cast iron, nonferrous metalsand alloys,variousannealedsteelafterquenching, especiallyfor thesoftermetals such asaluminum, lead,tin and otherferrous metals,nonferrous metalsBrinellhardness test.
工作环境/ Work environment:
1、在室温10~35℃的范围内;
2、在稳固的基础上水平安装;
3、在无震动的环境中;
4、周围无腐蚀性介质;
5、室内相对湿度不大于65%;
1, in the range of room temperature 10~35℃;
2, in a stable foundation for horizontal installation;
3, in the absence of vibration environment;
4,Non corrosive medium, around;
5, the indoor relative humidity of not more than 65%;
独有优点/ Unique Advantages:
1The latestC + +programminglanguageprecision pressuresensor+ CPU+closed loopcontrol system to ensureaccuracy andexcellentvalueas thevalue ofthe forcestability;
2 significantly improve the reliability and stability of the hardware in the running;
3 fluctuations in the value of the dynamic force of less than 1000/1 (the other production companies 1000/5);
4 to ensure a more accurate force values????, showing the value of a more stable;
5 casing done aging treatment;
6 has good maneuverability and humane;
7 Brinell test force: ten
8dynamic displaytest forceloading, unloadingof the entire process;
技术指标/Technical Index:
1.试验力:612.9N(62.5kg)、980.7N(100kg)、1226N(125kg)、1839N(187.5kg)、2452N(250kg)、4903N(500kg)、7355N(750kg)、9807N(1000kg)、14710N(1500kg)、29420N(3000kg)
2.压头规格:
2.1 φ2.5mm球压头
2.2 φ5mm球压头
2.3 φ10mm球压头
3.测量显微镜放大倍率:20X
4.测微毂轮最小读数:0.005mm
5.被测试件允许最大高度:225mm
6.压头中心到机身距离:135mm
7.延时控制:5~60秒可调
8.电源电压:AC220V±5%,50~60Hz
9.硬度计外形尺寸(长×宽×高) 789×543×225 (mm)
10.仪器重量约:130kg
11.试验力的选择应使压痕直径(d)与球直径(D)保持0.25D<d<0.6D的关系.
12.硬度测试范围:8~650HBW
13.试验力加载:全自动
1 Atest force:. 612.9N (62.5kg), 980.7N (100kg), 1226N (125kg), 1839N (187.5kg), 2452N (250kg), 4903N (500kg), 7355N (750kg), 9807N (1000kg), 14710N(1500kg), 29420N (3000kg)
2headSpecifications:
2.1 φ2.5mmball indenter
2.2 φ5mmball indenter
2.3 φ10mmball indenter
3Measuring Microscopemagnification: 20X
4micrometerHubMinimum reading: 0.005mm
5were allowed totest themaximum height: 225mm
6indentercenter to the fuselage: 135mm
7Delay Control:adjustablefrom 5 to60 seconds
8Power supply voltage:. AC220V ± 5%, 50 ~ 60Hz
9Hardness Dimensions(L × W× H) 789 × 543 × 225 (mm)
10Instrumentweight about: 130kg
11Select thetest forceshallmakeindentation diameter(d)maintaining0.25D <d <0.6Drelationship with theball diameter(D).
12Hardnesstest range:. 8 ~ 650HBW
13testforce loading: Automatic
标准配置/ Standard configuration:
1.主机
2.20×读数显微镜1只
3.φ2.5mm球压头1只
4.φ5mm球压头1只
5.φ10mm球压头1只
6.小平面试台1只
7.大平面试台1只
8.标准布氏硬度块
HBW/3000/10 1块
HBW/750/5 1块
9.保险丝2只
10.电源线1根
11.产品合格证书1份
12.产品使用说明书1本
13.布氏硬度对照表1本
14.防尘罩1只
选配附件/ Optional accessories:
压头、硬度块
客户名录:
详见公司客户名录
、、、、、、
质量保证:
本公司保证交付的硬度计执行标准:金属布氏硬度实验GB/T 231-2002国家标准、JJG_150-2005布氏硬度计检定规程,参照ISO 6506:2005国际标准。精度达到合同要求。生产研发过程严格执行ISO9001:2000质量管理体系.
We guaranteedeliveryofStandardHardness:Brinellhardness testGB / T 231-2002national standards, JJG_150-2005Brinell hardnesstest procedures,referring toISO 6506:2005international standard.Accuracyrequirements of the contract.Production and developmentprocess strictlyimplement ISO9001: 2000quality management system.