首页 > 产品信息 > 工业设备 > 服装、服饰加工设备

自动旋转四工位T恤烫画印花机械 1
  • 自动旋转四工位T恤烫画印花机械 1

自动旋转四工位T恤烫画印花机械

型号:ZS-C
品牌:至上
原产地:中国
类别:工业设备 / 服装、服饰加工设备
标签︰T恤烫画机 , 多功能烫画 , 杯子印花机
单价: ¥12000 / 台
最少订量:1 台
发送查询 添加到查询篮

会员信息

详细信息

钟卓万(个人账号)

免费会员广东省东莞市
即时通讯:最后上线︰2010/08/17

产品描述

产品型号: ZS-C名      称:自动四工位烫画机 产品用途:广泛用于纺织布料制品,陶瓷制品,金属制品的热转印印花或热处理.适用于烫印服装、手袋、雨伞、鞋、帽、工艺品、礼品、广告用品等。可将发泡烫画、渗透烫画、幻彩烫画、升华烫画、植绒烫画、烫金烫画、泳装烫画、电子科技影像烫画、烫钻、烫珠、烫胶等转印到自己所需要烫印物品上。     产品特点;

●采用 控制系统、进口元件、自动限位、体积小、性能强(准确、安全)、使用寿命长;
●PID微电脑控制,精确度高( 1℃);
●时间全数字化显示,准确度高;
●进口优质加热板材料,且采用油加温发热液体循环导热发热均匀,热导性强;
●外观精美。
 
技术参数:电 压:110v 220V  380V 功 率:2250W 温度范围:0-399℃ 时间控制:0-999ses 气   压:8kg 工作台尺寸:38*38  40*40  40*50  40*60  60*80 cm 包装 尺寸:150*80*160  160*80*160  170*80*160 cm 重    量:150kg  160kg  170kg 操作流程:
启动电源开关,将温度、时间、气压调至所需要求;
温度达到时,请先试烫所需产品,将开关转换至“手动”位置,确认试烫产品质量认可后方可转换至“自动”位置批量生产;
当开关至“手动”位置时,用手按动“手动启动”发热板向下压直至时间到后自动上升,如:烫印过程中发现位置不对,则按一下“紧急停止”中止烫压,当开关至“自动”位置时,只需将发热板推到位刚发热板自动下压。 注意事项:
整机必须有合适牢靠的地线保护。 维护事项:
气压:如压力不够或太大,可调气瓶上调压阀,向(+)方向加大压力,向(—)方向减小压力(请注意气瓶是否有润滑油);
温度:当设备到达设定温度后发热板不发热或发热不匀,请检查温控器接线同时确认热电偶是否有损坏;
时间:当开关至“手动”时,按动“手动启动”若不会下压则检查“手动”开关,当开关至“自动”时,台板到位时不会下压,应检查箱内微动开关接触点是否到位,如不同位则应该调整;
如出现质量问题,请及时与本公司联系。
Product Description

Name:  Auto 4 table revolving printer

  Model:GB-C3838  GB-C4050  ZS-C4060  GB-C6080 parameter:   Voltage:110v  220v  380v power:2250w Temperature range:0-399℃ Time range:0-180sec Air pressure:0-8kg Work table size:30*38 40*50 40*60 60*80 (cm) Casing size:105*80*160 160*80*160 170*80*160 (cm) Avoirdupois:150kg  160kg  170kg   Use: This machine can press sublimation, impregnant printing ink color picture on cotton, hemp, fibre and another fabric by heat press, it also can use in technics heat treatment as transplanting fur painting and froth printing. This aircraft electric appliance control uses the most vanguard technology, four revolving work the floor, the automatic spacing, the accurate security, the reliability is high, service life is long, electronic digit constant temperature control, precision high (±1-2℃). is your assembly line work best choice   Characteristic : 1. Using the most advanced control system, import element, auto fixing position , high capability for accuracy and safety ,long use lifetime .
2. PID Micro-computer controller .high precision ( 1℃)
3. Full digital time show, high accuracy
4. High quality import heat plate material . adopt with both air vacuum heating and oil heating devices maintaining consistent heat and strong heat exchange .
5. appearance is beautiful and fashionable
  Operation:   1.      turn on the switch of power , adjust the temperature ,time and air pressure to the requirement . 2.      when temperature reaches the set point ,please print the test sample firstly ,adjust the switch to “ manual “ position, confirm the quality of test sample is passed , then can adjust the switch to “ automatic “ to produce as a batch when the switch was on “ manual “ position , please press the “ manual start” button ,the heating-plate will press down until the time is end then will automatic rise . eg: when find it is not the right position during the print process, should press “ urgent stop” button to stop print . when the switch is on “ automatic” position , just put the heating-plate to the right position then it can automatic press down. Notice : Must have a suitably and firm earth wire protection Maintenance:   1. air pressure : if the pressure is not enough or too much , you can loose or increase the pressure screw to adjust, turn to“ + ”for increase pressure , turn to “–” for loose pressure ( please note if has lube on the air-jar ) 2.temperature :when the temperature reaches to the set point while the heating-plate doesn’t work or heating not equality , please check if the temperature controller is turn on or circuit is destroyed. 3. time : when the switch turn on “ manual “ position  but can’t press down when press the “ manual start “ button , please check “manual” switch . when the switch turn on “ automatic “  the board reaches the position but can’t press down, please check the mirco- switch if connect correctly in the box , please adjust if not . 4. please contact us if have any quality problem

 


付款方式︰现金/银行转账

产品图片

自动旋转四工位T恤烫画印花机械 1
图 1

向该会员发送查询

钟卓万(个人账号)

广东省东莞市虎门镇怀德工业区

电话︰
86-0769-81611560
传真︰
86-0769-81515750
联系人︰
钟卓万 (销售部总经理)
手机︰
13424888830

该公司相关产品信息

免责声明:以上信息由企业自行提供,内容的真实性和合法性由发布企业负责。「自助贸易」对此不承担任何保证责任。
举报投诉:如发现违法和不良资讯,请 点此处举报

中国供应商快速搜索︰

"服装、服饰加工设备" 产品信息

"服装、服饰加工设备" 供应商